If it uses an external router for internet connectivity, WANIPConnection1has to be used instead. As I am new to this: Which rule would I need to test if LAN->WAN->FritzBox->Internet works? I have tried MAC cloning and changing the IP address to 192.168.2.1 but the problem is not solved. - Which setup for WAN is right? Does this work, or do I need to assign Fritzbox and WAN the same address/mask? December 21. Since FritzOS! Make a note of this information or print out the page. I have been looking around from other QnAs and it seems that I have to configure the NAT in order to connect to the VPN from other wifi connections. Fritzbox (192.168.178.1) and pfsense(192.168.1.1) have different subnets The nginx server should be accessible on port 80 from the Internet. The patch adds the option to ⦠Thx for any guidance. Exposed Host is configured on the FritzBox. If the wanBlockIPs parameter is set, a channel for each IP is created to block/unblock WAN access for this IP. 0. And if plugging in a Fritzbox I get addresses too. De Fritzbox is DHCP server voor het Home netwerk (eigen thuisnetwerk) die aan de NAS en printer vaste IP adressen heeft toegekend. Highly appreciate your time, Yours Votan ip tunnel add gre1 mode gre local (ip vom NetcupVPS) remote (IP vom WAN der Fritzbox - öffentliche IP vom ISP) ttl 255 ip addr add 172.20.1.1/30 dev gre1 #subnet zur kommunikation der beiden GRE endstellen 1 ist vps 2 ist die pfsense#
ip link set gre1 up ip route add 172.20.1.2 dev gre1 ip route add (zusätzlicheipvonnetcup) dev gre1 Maybe you need this Port on the Firewall´s WAN Port too.--Thomas. Note: When the settings are applied the FRITZ!Box automatically obtains a new IP address, and as a consequence, a new network address range. Tried changing "Block private" and "Block bogon" already, although should not have an effect, because the WAN IP I should be getting is 100.64.74.29/16. This tp-link wireless router was purchased to replace a FritzBox router which only has one LAN port and no WiFi. Values need to be IPv4 addresses in the format a.b.c.d. In the process of setting up the tp-link router, I am getting the message âWAN port is unpluggedâ and the router does not connect. I tried FRitzbox with a static IP (192.168.0.1) and WAN with DHCP. The VPN is actually accessible through the WAN IP when I am connected to the Fritzbox router, but I cannot access the VPN when connected to another wifi connection or mobile hotspot data. Hi @J_de_Haan_2020. Reading the WAN IP via the FritzBox SOAP service API WANPPPConnection1 only works if the FritzBox establishes the PPP connection itself. The Exposted Host is configured on IP Adress 192.168.188.2. So far, I have configured my firewall rules so that I can access the nginx server from my LAN and also that I can perform ping and nslookup from the rPI to the WAN⦠Changed firewall to allow any incoming traffic ⦠The FRITZ!Box now can be reached at the new IP address. Page 175 ⢠IP telephone settings: connected with the FRITZ!Box directly or via FRITZ!App Fon FRITZ!Box users ⢠All FRITZ!Box users and their rights to access FRITZ!Box contents, for the FRITZ!Box home network and for access from the Internet ⢠Time at which the FRITZ!Box last logged in and the IP ⦠7.20 WAN access of local devices can be controlled by their IPs. The Ftitzbox has IP Adress 192.168.188.1. Chris Administrator. ... And have a look for managment of the Fritzbox from WAN side. A separate window presents an overview of the new network address information.